收藏本站
SAW Components
SAW RF filter
B3563
864.00 MHz
Data sheet
ESD protection of SAW filters
SAW filters are E lectro S tatic D ischarge sensitive devices. To reduce the probability of damages
caused by ESD, special matching topologies have to be applied.
In general, “ESD matching” has to be ensured at that filter port, where electrostatic discharge is
expected.
Electrostatic discharges predominantly appear at the antenna input of RF receivers. Therefore
only the input matching of the SAW filter has to be designed to short circuit or to block the ESD
pulse.
Below three figures show recommended “ESD matching” topologies.
For wideband filters the high-pass ESD matching structure needs to be at least of 3 rd order to
ensure a proper matching for any impedance value of antenna and SAW filter input. The required
component values have to be determined from case to case.
Cs1
Cs3
Cs1
Cs3
Lp2
to output
matching
Lp2
to output
matching
Fig. 1 MLC varistor plus ESD matching
Fig. 2 Suppressor diode plus ESD matching
In cases where minor ESD occur, following simplified “ESD matching” topologies can be used
alternatively.
Cs1
Cs3
Lp2
to output
matching
Fig. 3 3 rd order high-pass structure for basic ESD protection
In all three figures the shunt inductor Lp2 could be replaced by a shorted microstrip with proper
length and width. If this configuration is possible depends on the operating frequency and
available pcb space.
Effectiveness of the applied ESD protection has to be checked according to relevant industry
standards or customer specific requirements
For further information, please refer to EPCOS Application report:
“ ESD protection for SAW filters ”.
This report can be found under www.epcos.com/rke.Click on “Applications Notes”.
Please read cautions and warnings and
important notes at the end of this document.
5
October 21, 2013
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
B39871B3715U410 FILTER SAW 869MHZ REMOTE SMD
B39871B3716U410 FILTER SAW 869MHZ REMOTE SMD
B39871B3717U410 FILTER SAW 866.5MHZ SMD
B39871B3725U410 FILTER SAW 869.0MHZ SMD
B39871B3734H110 FILTER SAW 868.3MHZ SMD
B39871B3744H110 FILTER SAW 868.30MHZ SMD
B39871B3746H110 FILTER SAW 868.60MHZ SMD
B39871B3903U510 FILTER SAW 869.0MHZ SMD
相关代理商/技术参数
B39861B3589Z810 功能描述:信号调节 B3589 FRONTEND FILTER RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39861B3706Z610 功能描述:信号调节 FILTER RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39861B3821Z810 功能描述:信号调节 LOW LOSS 860.50MHZ RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39861-B3821-Z810 制造商:EPCOS 制造商全称:EPCOS 功能描述:SAW Components Low-loss Filter 860,5 MHz
B39861B4114U410 功能描述:FILTER SAW 862MHZ LOWLOSS SMD 制造商:qualcomm (rf360 - a qualcomm & tdk joint venture) 系列:- 包装:带卷（TR） 零件状态:停產 频率 - 中心:862MHz 带宽:30MHz 插入损耗:2.8dB 应用:移动电话 安装类型:表面贴装 封装/外壳:6-SMD，无引线 高度（最大值）:0.043"（1.10mm） 大小/尺寸:0.118" 长 x 0.118" 宽（3.00mm x 3.00mm） 标准包装:9,000
B39861-B4114-U410 制造商:TDK Epcos 功能描述:
B39861B4161U410 功能描述:信号调节 LOW LOSS 860.50MHZ RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39861-B4161-U410 制造商:EPCOS 制造商全称:EPCOS 功能描述:Low-Loss Filter for Mobile Communication